Exactly How to Install a Bath Tub
Exactly How to Install a Bath Tub
Blog Article
Right here in the next paragraph you might get some quality points relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately challenging job. If the old tub is readily accessible, the task can relocate immediately; if you need to open a wall to remove the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as set in the new one. Ensure you have qualified yourself for the work and also fit attempting it. Rather than hiring a service provider to take over a halfway-completed project, it is better to take into consideration utilizing one before you begin. Opportunities are you may need a professional plumber to make tube links.
This post will help you mount a new bathtub in your washroom if you have actually already bought a brand-new tub and do not require to change the setup of your previous supply of water pipelines.
Your devices and product checklist should consist of the following:
Getting ready for the Installation
Firstly, the sustaining structure provided with the bath should be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, then the first thing you should do is detach the water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of eliminating the existing taps can be fairly problematic as a result of the restricted access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any old securing compound.
Before going on to fit the new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, place the bath tub in the required setting. The wood boards are helpful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub until the spirit level reads level.
To set up taps, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the tub must wait up until the tub has actually been used at least once as this will settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washers remain in place between the tap and also the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to split a rigid seal, creating the water to permeate the wall in between the bath and the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can fracture fairly very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the market. It is a good idea to fit the floor tiles using waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that post on Tools You Need to Install a New Bathtub when doing a search on the search engines. Are you aware of somebody who is truly interested in the niche? Please feel free to promote it. I am grateful for your time. Kindly check our blog back soon.
Schedule A Service Report this page